Advertisement

Article

Signal Chain Basics #73: Audio metering, enjoying the VU

Audio metering is present in almost any equipment that plays or records audio – from cell phones displaying bar graphs of audio output levels, to home stereos with flashing LEDS, to live broadcasting.

There are multiple standards for audio metering that deal with the levels being monitored and time constants used for calculating the average. The behavior of volume unit (VU) meters is defined in ANSI C16.5-1942, British Standard BS 6840, and IEC 60268-17. These standards define 0 VU = +4d Bm, with an integration time of 300 ms. Traditionally, with a moving needle meter, this means that from zero signal to 0 VU, the needle should reach 0 VU within 300 ms (same for decay). This makes a traditional VU meter excellent for getting an idea of loudness, but a poor method for monitoring transients. This was fine in traditional broadcast and recording systems, mainly based on tubes and tape, both of which tend to saturate elegantly.

In today's digital systems, clipping inputs or outputs sounds awful, so peak program meters (PPM) are used. PPMs are similar to VUs, but, integration time is much faster (typically around 10 ms). Note that there are multiple standards bodies with definitions for the signal levels and exact integration times. Display technology is a big part of these standards. Getting the ballistics right to move a needle through 90 degrees (or more) with one percent of accuracy is much harder and slower than lighting a few LEDs!

Using LEDs, the quality of audio monitoring varies drastically. For example, a simple voice recorder product requires a different metering system from a mini-micro system using LEDs as a visual effect. In a live sound or broadcast environment accuracy is important, as well as seeing the difference between average loudness and the signal’s absolute peak.
    
Most meters can be split into two sections: a front-end and comparator circuit (Figure 1 ).

 


Click on image to enlarge.

Figure 1. Two-part block diagram with a front-end and a comparator set up.

Signal conditioning

Signal conditioning happens in the front-end. Three things should be done at this point, plus an optional item:

  1. Audio level gain/attenuation to configure what voltage should equate to highest LED/meter value
  2. Integration time (for example, 300 ms for VU, <10 ms for PPM, etc.)
  3. Signal rectification
  4. Optional: peak-hold vs direct signal circuit

Signal rectification is required mainly in comparator-style systems. Full signal rectification is required because not all signals are symmetric. The acoustic output of some musical instruments (and some voice) shows more pressure on the microphone in one direction. To monitor this accurately, the signal should be fully rectified. Be sure to compensate for the usual 0.7 V diode drop.

Figure 2 shows a full wave rectifier circuit. Such a circuit can be implemented in a very small space, using BAV99 dual diodes in a SOT23 packages, and 100 kOhm resistor networks. For small voltage systems (3.3V), a quad low-voltage rail-to-rail output operational amplifier (op amp) such as the LMV324 can be used in a single supply system, but ground should be replaced by Vcc/2. The dual output op amp used in this example is the LF353, because of its low cost, high impedance input, and wide voltage range support (±15V).
 


Click on image to enlarge.

Figure 2. Full wave rectifier circuit.

Figure 3 is an example schematic of a signal rectification and VU integrator.


Click on image to enlarge.

Figure 3. Full wave rectifier with VU integrator

For systems that require monitoring peak versus direct signal (with its integration time), a peak-hold circuit (or code) can be used. In software this can be implemented by storing the ADC’s largest peak value in a separate register and holding it for a specific number of samples. Whenever a new larger sample is received, simply overwrite the peak value and reset the counter. When the counter finally hits zero, reset the peak value to zero.

In an analog circuit, the rectified output can be run through the circuit in Figure 4 . D1 biases the output up a diode drop (~0.7V), and is then dropped 0.7V by D2. D2 ensures that audio content can only flow into C1 and R1, not back through the feedback circuit. The values of C1 and R1 set the decay time for the peak hold. The impedance of the comparator array ADC also acts as impedance to ground.


Click on image to enlarge.

Figure 4. Example peak-hold circuit.

References

Download these datasheets: www.ti.com/lmv324l-ca, www.ti.com/lf353-ca.

Please join us next month when we discuss using band limited dither to improve SFDR in high-speed DACs

Other Signal Chain Basics in the series can be found here .

2 comments on “Signal Chain Basics #73: Audio metering, enjoying the VU

  1. ljljvwoei
    April 17, 2014

    To find a good printer in Canada. I would suggest using the following companies: Toronto Printing Companies | Calgary Printing Companies | Winnipeg Printing Companies | Montreal Printing Companies | Regina Printing Companies | Saskatoon Printing Companies | Quebec Printing Companies | Ottawa Printing Companies | Edmonton Printing Companies | Vancouver Printing Companies | These companies provide the best and most affordable price in whole Canada. Other printing companies I suggest would be Print Quote Services | Printing Company | Best Local Printer | Some other local cities have great printers as well such as the following: Philadelphia Printing | Memphis Printing | San Francisco Printing

    If you are looking to print custom stickers. The following is my best choice: Label and sticker printing | Print Custom Sticker | Print Stickers | No only they offer the best sticker printing quality but also unbeatable price.

    Nowadays, it is hard to find quality print trader. This is my recommendation for best print trader in the united states Best Print Trader | Lowest Price Printing Wholesale | Print Outsourcing | Print Broker Trade

    Lastly, all print should comes with a state of the art Print Management Software. I would highly recommend this print software tool.

  2. dianabolbulk
    August 28, 2016

    Dianabolbulk I like the article so much it has got my attention. I feel that people should ask more questions about this topic so that curiosity of people should increase. I am glad to find this article because it is really helpful to me. Thanks for legal steroids for sale this article once again.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.